For Customer Use:Model No.Serial No.Enter below the Model No. and Serial No.which are located on the rear, bottom orside of the cabinet. Retain this i
5Names of the PartsPOWER button and STANDBY lamp (for Canada and U.S.A) button and STANDBY lamp (for other countries)Press to turn the power on or to
6EnglishCD CONTROL operation buttonsPLAY MODE: Press repeatedly to select one of the play modes forthe 3-CD changer. (See page 15 and 16.)CD EDIT: Pre
7CD numbers and play status displaysIndicate whether discs are loaded in any of the 3-CD changer disctrays, which disc is currently selected, and the
8EnglishWhen performing the procedures in this manual,the buttons on the remote control have the samefunction as the corresponding buttons on the main
9Using the Remote Control1 Press down on the point shown by the arrow at the top of the compartment cover, and pull up the cover to open the compartme
10EnglishPower ON/STANDBY OperationsTo turn on the powerPress the POWER (for Canada and U.S.A.)/ (for other coun-tries) button on the front panel or
11Listening to CDsExample: When starting playback at CD1.1 Press the CD1 0 button to open the CD tray.• The power comes on, and the CD1 tray opens.2 L
12EnglishConcerning the CD numbers and play status displayThe display shows for each CD tray whether or not a CD has beeninserted as well as the play
13• Pressing the CD 1, CD 2, or CD 3 buttons automatically sets themain unit to the CD function and starts playback of the disc inthe selected tray.•
14EnglishTo skip forward or backward to different tracks on the currentlyselected CD, use the MULTI JOG dial on the unit or the 4 or¢ buttons on the r
G-1Warnings, Cautions and OthersFor U.S.A.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
15The random play mode can be selected by pressing the PLAYMODE button repeatedly on the main unit or remote control whenthe function is in the CD sto
16EnglishUp to 32 tracks can be programmed. Any tracks on CD1, CD2 andCD3 can be selected.1 Insert CDs that contain tracks to be programmed.• Tracks o
171 Load the CDs whose tracks are to be programmed into the 3-CD changer.2 Press the PLAY MODE button while the unit is in the CD stop mode to select
18EnglishRecording onto CD-R and CD-RWNotes on Recording• Do not use CD-R or CD-RW with dust and/or small scratcheson the surface as this may cause th
194 When analog signals are to be recorded, adjust the recording level.The OVER indicator should not be made to light as this may causedistortion in t
20EnglishTo add track marks manually1 In the procedure above, set the automatic track setting to“AUTO TR OFF”. 2 During recording, press the SET butto
212 Insert a recordable CD-R or CD-RW in the CDR disc tray.3 While the disc is playing back the track you want to record or if that track is being pau
22EnglishWhen the first track has been stored in memoryNote• When there is not much recording time left on the CD-R or CD-RW, tracks that are longer t
235 Select and enter the program source.• The source can be selected in either direction using the MULTIJOG dial on the main unit or the 4 and ¢ butto
24English5 Turn the MULTI JOG dial or press the 4/¢ button on the remote control to select “DUB-SPEED 2X” or “DUB-SPEED 1X”.• If “DUB-SPEED 2X” is sel
G-2CAUTIONTo reduce the risk of electrical shocks, fire, etc.:1. Do not remove screws, covers or cabinet.2. Do not expose this appliance to rain or mo
25Perform synchronized start recording of sources such as DAT andCD connected to either the DIGITAL IN OPTICAL connector orLINE IN (REC) connectors on
26English1 Load a recordable CD-R or CD-RW in the CDR disc tray.2 Press the REC ¶ button on the main unit to put the CDR in the record pause mode.• Th
27Special Recording Edit Operations Occasionally, there may be tracks on a disc that are partial,repeated, or are otherwise unwanted . Before a CD-R o
28English4 Press the SET button.• “ERASE (start track) – (last track)” appears in the display. (Ini-tially, the start track and the last track are bot
29 Finalization marks the final process in recording on a CD-R or CD-RW in which the TOC (Table Of Contents) is written to the disc.When this procedur
30EnglishOnce a CD-R has been finalized, further recording on that disc can-not be performed. However, by erasing the TOC (Table of Con-tents) on a CD
312 Turn the MULTI JOG on the main unit or press the 4 and ¢ buttons on the remote control until “CONVERTER” appears in the display.3 Press the SET bu
32EnglishBy performing the following procedure, all menu settings stored inthe unit are cleared and the unit is reset to the factory default set-tings
33Setting the Clock(To be performed when the unit is to be used for the first time)Example: Setting the time to 1:15 PM (while the power is switched t
34EnglishTimer OperationsBefore proceeding with timer programming, make sure that thepresent time has been set correctly. (See page 33.)Example: Sett
G-3REPRODUCTION OF LABELS (Except for Canada & USA)1 CLASSIFICATION LABEL, PLACED ON REAR ENCLOSURE2 WARNING LABEL, PLACED INSIDE THE UNIT IMPORT
358 While “PLAY” is flashing, press the SET button9 Turn the MULTI JOG dial to set the function to CD or CDR.10 Press the SET button.• This display ap
36EnglishNotes• Match the timer of the connected source with the unit’s setting.(In the case of the mic input, ensure that the microphone hasbeen conn
37COMPU LINK FunctionWhat is COMPU LINK?The COMPU LINK remote control system (or, simply, “COMPU LINK”) serves to enable the kind of simple operations
38EnglishCD and CDR MessagesCD MessagesMessage Significance Remedy CD * NO DISC (* indicates the disc tray number)There is no disc in the selected tra
39Message Significance Remedy CD-ROM DISC The inserted disc is a CD-ROM. Record and erase functions are not possible. Replace with a disc recorded for
40EnglishRestriction on Copying Digital MaterialDue to copyright and other considerations, the following restrictionis now in place for CD-R and CD on
41TroubleshootingIf the unit fails to operate properly even when the remedial action suggested above has been taken:This unit uses a microcomputer to
42EnglishMain SpecificationsThe unit’s specifications and exterior are subject to change withoutnotice due to improvements.CD Player SectionSystem Co
VICTOR COMPANY OF JAP AN, LIMITEDJVCDIGITAL INOPTICALDIGITAL OUTOPTICALMODECDR TDCOMPU LINK-4(SYNCHRO)LINEIN REC( )OUT PLAYLEFTLEFTRIGHT
G-4Caution: Proper VentilationTo avoide risk of electric shock and fire and to protect from damage.Locate the apparatus as follows:Front: No obstructi
1Table of ContentsIntroduction ...1Table of Contents ...
2EnglishPrecautionsThank you for purchasing this JVC product. Please read theseinstructions through carefully before starting operation to ensurethat
3ConnectionsDo not turn on the power until all the connections have been completed.Use the accessory pin cables to connect this unit’s LINE connectors
4EnglishBefore proceeding, check whether the optical digital cable can be connected.• Connect a receiver or amplifier with digital audio capability to
Kommentare zu diesen Handbüchern