JVC RX-6500VBK Bedienungsanleitung PDF herunterladen (Seite 16)

English

Crossover Frequency Setting

Small speaker cannot reproduce the bass sound very well. So, if you

have used a small speaker any for the front, center, or rear channels,

this receiver automatically reallocates the bass elements, originally

assigned to the channel for which you have connected the small

speaker, to another channel (for which you have connected the large

speaker).

If you have selected “LARGE” for all speakers (see page 12), this

function will not take effect. To use this function properly, you need

to set this crossover frequency level according to the size of the

small speaker connected.

This function takes effect in the following cases:

- When playing a source using Dolby Pro Logic, Dolby Digital,

or DTS Digital Surround.

- When using the DAP modes.

On the front panel ONLY:

1. Press SETTING repeatedly until

“CROSSOVER FRQ” (Crossover

Frequency) appears on the display.

• Once you have pressed SETTING, MULTI CURSOR % / ﬁ

can be also used for selecting “CROSSOVER FRQ.”

• The display changes to show the current setting.

2. Press MULTI CURSOR @ / # to

select the crossover frequency level

according to the size of the small

speaker connected.

• As you press it, the display changes to show the following:

• Use the following comments as reference when adjusting.

80Hz: Select this when the cone speaker unit built in the

speaker is about 12 cm.

100Hz: Select this when the cone speaker unit built in the

speaker is about 10 cm.

120Hz: Select this when the cone speaker unit built in the

speaker is about 8 cm.

SETTING

MULTI CURSOR

80Hz 100Hz 120Hz

Low Frequency Effect Attenuator Setting

If the bass sound is distorted while playing back a source using

Dolby Digital or DTS Digital Surround, follow the procedure below.

• This function takes effect only when the subwoofer (LFE) signals

come in. (with “SUBWOOFER” set to “Yes.”)

On the front panel ONLY:

1. Press SETTING repeatedly until

“LFE ATT” (Low Frequency

Effect Attenuator) appears on the

display.

• Once you have pressed SETTING, MULTI CURSOR % / ﬁ

can be also used for selecting “LFE ATT.”

• The display changes to show the current setting.

2. Press MULTI CURSOR @ / # to

select the low frequency effect

attenuator level.

• As you press it, the display changes to

show the following:

0dB: Normally select this.

10dB: Select this when the bass sound is distorted.

Dynamic Range Compression Setting

You can compress the dynamic range (difference between maximum

sound and minimum sound) of the reproduced sound. This is useful

when enjoying surround sound at night.

• This function takes effect only when playing back a source using

Dolby Digital.

On the front panel ONLY:

1. Press SETTING repeatedly until

“D. RANGE COMP.” (Dynamic

Range Compression) appears on

the display.

• Once you have pressed SETTING, MULTI CURSOR % / ﬁ

can be also used for selecting “D. RANGE COMP.”

• The display changes to show the current setting.

2. Press MULTI CURSOR @ / # to

select the appropriate item about

the compression level.

• As you press it, the display changes to

show the following:

OFF: Select this when you want to enjoy surround with its

full dynamic range. (No effect applied)

MID: Select this when you want to reduce the dynamic

range a little. (Factory setting)

MAX: Select this when you want to apply the compression

effect fully. (Useful at night)

SETTING

MULTI CURSOR

0dB 10dB

OFF MID MAX

SETTING

MULTI CURSOR

EN08_17.RX-6500V[J] 99.12.16, 1:08 PM13

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 40 41

Kommentare zu diesen Handbüchern

Keine Kommentare

JVC RX-6500VBK Bedienungsanleitung Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für AV-Receiver JVC RX-6500VBK