JVC KV-V8 Bedienungsanleitung

MOBILE VIDEO CASSETTE PLAYERNo.49625Feb. 2001COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD.KV-V8Area SuffixEJContinental EuropeNorth AmericaContent

1-8-0 -7 - Initial value-1 -0 - EJECT position- - -0 EJECT position (Cassette housing drive mode)-2 -7 - Housing operating- - -1 Between EJECT and U /

2-1SECTION 2MECHANISM ADJUSTMENT2.1 Before starting repair and adjustment2.1.1 Precautions(1) Unplug the power cord plug of the VCR before using your

2-22.1.5 Maintenance and inspection1. Location of major mechanical partsFig. 2-1-5a Mechanism assembly top sideFig. 2-1-5b Mechanism assembly bo

2-32. CleaningRegular cleaning of the transport system parts is desirablebut practically impossible. So make it a rule to carry out clean-ing of the t

2-42.2 Replacement of major parts2.2.1 Before starting disassemblingThis mechanism has an exclusive operation mode providedfor disassembling and inst

2-52.2.6 Loading motor(1) Remove the belt from the worm gear assembly.(2) Take out the 2 screws (A) and then remove the loadingmotor.Note:• When insta

2-6Fig.2-2-9b2.2.10 Control plate(1) Take out the slit washer, disengage the 2 hooks whilelifting the control cam side of the control plate, and re-mo

2-72.2.13 Change lever assembly, rotary encoder(1) Slide the change lever assembly in the direction of thearrow and remove.(2) While pushing the claws

2-82.2.16 Guide rail(1) Take out the 5 screws (A) and 1 screw (B).(2) By expanding the rails on the outer sides of the guiderail, remove the 2 pole ba

2-92. How to install(1) Clean the coil parts of the lower drum assembly and thenewly installed upper drum assembly with an air brushin advance. (See F

Specificatios (KV-V8J)General•Power supply : DC12 V (11V-16V allowable)Negative ground•Dimensions : 259 mm x 94 mm x 270 mm (10-1/4"x 3-3/4"

2-10Fig. 2-3-2a2.3.2 Loading arm assemblies (supply, take up)(1) Attach the loading arm assembly (supply) and loading armassembly (take up) so that th

2-112.3.5 Control plate(1) Attach the control plate by aligning the 2 alignment holeson the control plate with the alignment holes on the maindeck ass

2-12Fig. 2-5-1aImproper waveform variationMax levelMin level Proper waveform variationFig. 2-5-1b1.25mmRoller driverHexagonal wrenchTightenLoosenGui

2-13Fig. 2-5-1dImproper Proper( a ) Guide roller( b ) Guide poleFig. 2-5-1cABCDLevel drop at the guide roller (supply side)Level drop at the guide rol

2-142.5.4 Standard tracking presetFig. 2-5-3bFig. 2-5-3aAlignment tape [SP, stairstep]played with the SP headAlignment tape [EP(LP), stairstep]played

3-1SECTION 3ELECTRICAL ADJUSTMENT3.1 PrecautionThe following adjustment procedures are not only necessaryafter replacement of consumable mechanical pa

3-23.2.2 Slow tracking presetSignal (A1) • Color (colour) bar or stairstep signal[KV-V8E](A2) • Alignment tape [MH-2] or [MHPE](A3) • Alignment tape [

Printed in Japan200102(S) No.49625VICTOR COMPANY OF JAPAN, LIMITEDMOBILE ELECTRONICS DIVISIONPERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome

1-1[1] Top cover D12(S1a), (S1b), 2(S1c)[2] SW board assembly, D22(S2a), (WR2a), stay<Note 2a>Front panel assembly 4(L2a), 3(L2b), <Note 2b&g

1-2Fig. D2 Fig. D3bFig. D3aFig. D1Rear sidePinch plateLoading motor beltControl camHole align with hole in deck<Note 3a> (S3a)(L3a)(L3a)[3]

1-3Fig. D4Fig. D6Fig. D5Not usedInertia plate[4]Drumassembly(S4b)< e >(L5a)WR4aSupportingtape side<Note 2a>WR4bSupportingtape side<N

1-4Fig. 1-4-1aMain board assemblySW boardassemblyFront boardassemblyCN3006CP5001 CP5002CN7001TP7002GNDTP7001MECHA TESTTP111D.FFTP4001CTL.PTP106PB FMTP

1-51.6 Emergency display functionThis unit has a function for storing the history of the past twoemergencies (EMG) and displaying them on each FDP (or

1-61.6.3 EMG content descriptionNote:EMG contents “E08/E09” are for the model with Dynamic Drum (DD).Table 1-6-3aWhen the mechanism mode cannot be ch

1-71.6.4 EMG detail information <1>The status (electrical operation mode) of the VCR and the sta-tus (mechanism operation mode/sensor informatio