DOME CAMERATK-C215V4TK-C215V12INSTRUCTIONS(A)For Customer Use:Enter below the Serial No. which is located on the body. Retain this information for fut
10IntroductionSet the video setting switches on the camera unit before mounting it.To set the switches, use a fine-tipped screwdriver.A [RESET/SPOT] R
114.[WHT.BAL.] ATW/MANUAL selection switch.For selecting whether to adjust the white balance automatically or manually.When the setting is changed fro
12IntroductionSet the video setting switches on the camera unit before mounting it.To set the switches, use a fine-tipped screwdriver. A [IRIS LEVEL]
132.[SELECT] WHT.BAL./PHASE setting switch.WHT.BAL.:The F [R/B, +/-] buttons are used as [R/B] adjustment buttons.PHASE:The F [R/B, +/-] buttons are u
14Installation and connectionThe maximum connection distance varies with the type of cable used. Please refer carefully to the table for each cable du
15Electrical Specifications of Alarm Input Terminals(TK-C215V12 only)● To prevent penetration of noise in the internal circuitry, apply a non-voltage
16Installation and connectionNOTE: ● Turn OFF the power supply to all equipment to be used befor
17Getting StartedCAUTION: ● When mounting the camera to the ceiling, ensure to wear safety glasses
18Installation and connectionEmbedding the camera to the ceiling* Make use of a ceiling material with a thickness between 9.5 mm to 22 mm.䡵 Setup1. Op
19䡵 Connecting1. Attach the fall prevention wire to the camera, followed by attaching it to the ceiling slab (Fall prevention wire is not included.)2.
2IntroductionSafety PrecautionsCAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK. DO NOT REMOVE COVER (ORBACK). NO USER-SERVICEABLE PARTSINSIDE.REFER SERVIC
20Installation and connectionWhen mounting the camera directly to the ceiling or on the wallWhen mounting to a wall, replace areas indicated as “ceili
214.Connect the video signal cable. (Apg. 14)Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to c
22Installation and connectionWhen mounting the camera to the electrical boxNOTE: Before mounting
23Adjusting ImageUpon mounting the camera, adjust the images while checking the actual image.Mounting the test monitorConnect the [MONITOR] terminal o
24Adjusting ImageAdjusting the field angle/focus/brightnessUpon determining the imaging direction, adjust the field angle, focus and iris level accord
25䡵 TK-C215V12● 2 types of angle of view may be selected for TK-C215V12. In general, set in a way such that the home position shoots a wide range and
26Adjusting Image䡵 TK-C215V12 (continued) Registering alarm positionFor registering the angle of view during monitoring when there is an alarm input.
27Other installation and adjustmentAfter setting is complete, mount the Inner dome.1. Mount the inner dome .Mount the inner dome to the claws (3 locat
28Other installation and adjustmentAs a general characteristic unique to CCDs, white-spots may appear on the screen with age.In order to reduce this p
29Others䡵 CameraSignal system: Based on NTSC standardScanning frequencies: 15.734 kHz (Horizontal), 59.94 Hz (Vertical)Image device: 1/4" IT CCDE
3I䢇 The unit is to be powered by a DC 12 V or an AC 24 V power supply.䢇 The unit is to be powered by a UL Listed DC 12 V or an AC 24 V power supply. 䢇
30Others䡵 External Dimensions [Unit: mm (inches)] When cover is attached* Specifications and appearance of this unit and related products are subject
31Focus chartTK-C215V4_V12_EN.book Page 31 Wednesday, August 2, 2006 1:18 PM
© 2006 Victor Company of Japan, Limited LST0420-001BTK-C215V4/TK-C215V12 DOME CAMERATK-C215V4_V12_EN.book Page 32 Wednesday, August 2, 2006 1:18
4IntroductionThese are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances.1. Read all of these instructions.2. Save these
5IntroductionSafety Precautions ... 2Contents... 5Charac
6IntroductionThank you for purchasing this product.(These instructions are for: TK-C215V4U/TK-C215V12U.)Before beginning to operate this unit, please
7䢇 To save energy, when it is not being used turn the system’s power off.䢇 This camera has been designed for indoor use. It cannot be used outdoors.䢇
8IntroductionCameraAMounting hole (elliptical) x 4Use these when mounting the camera to the electrical box. (A pg. 22)B Mounting hole (round) x 4Use t
9Camera (Interior)The dome cover, inner dome and outer case are removed.Procedures for removal. (A pg. 18 AEmbedding the camera to the ceilingB, Step
Kommentare zu diesen Handbüchern