JVC AV-20NX50 Bedienungsanleitung Seite 1

INSTRUCTIONSGGT0096-001A-HAV-21YS24AV-21YX50AV-20NX50ContentsKnowing your TV’s features ... 3Remot

10Adjusting the picture – USERYou can adjust the desired picture setting when selecting USERin PICTURE MODE.1 Select the USER in PICTURE MODE under PI

11BLUE BACKYou can set the TV to automatically change to a blue screen andmute the sound if the signal is weak or absent, or when there isno input fro

12Original features for pictureTELETEXTYou can watch the Teletext broadcast channel with TEXT function.1 Press the TEXT button to select the desired m

13SOUND SYSTEMYou can select an appropriate sound system when abnormalsound occurs even when the picture appears normally.Press the SOUND SYSTEM butto

14CINEMA SURROUNDYou can enjoy an enhanced sound for wider audience.Press the CINEMA SURROUND button to select a setting.OFF Cancel the function.LOW L

15To register the favorite channelYou can register and recall 4 favorite channels by using thecolour buttons (red, green, yellow, blue).1 In TV mode,

16VNRYou can reduce the picture noise.Select the VNR in the PICTURE FEATURES menu underPICTURE menu, then choose a setting of VNR function.OFF VNR is

17MENUINSTALL menuVIDEO-2 SETTING❇AUTO SHUTOFFYou can set the TV to turn off automatically when no signal isreceived for about 15 minutes or longer af

18To register the TV channels automaticallyYou can register the TV channels into the TV’s channel listautomatically.1 Display the INSTALL menu.2 Choos

19To add in the new channel(INSERT in the EDIT menu)You can add in the new channel in the TV channel list as you like.You need to find the “CH/CC” num

215 cm 10 cm 10 cm 15 cmWARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.CAUTION: TO ENSURE PERSONAL SAFETY,

20TV channel presetting (continued)CH/CC numberWhen you want to use the INSERTfunction on page 19, find the CH/CCnumber corresponding to the channelnu

21VLRRL/MONOYCBCR/VVLR/MONOOUTPUTVIDEO-1INPUTCOMPONENT(VIDEO-2)INPUTThe illustrations shown below is for AV-20NX50 and AV-21YX50only, which are used f

22TroubleshootingIf a problem occurs when you are using the TV, check the belowtroubleshooting guide before calling for repair.• Deactivate the BLUE B

23TV RF systemsB, G, I, D, K, MColour systemsPAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHzReceiving channelsVHF low channel (VL), VHF high channel (VH), UH

© 2005 Victor Company of Japan, Limited0405-FLE-JMTGGT0096-001A-H_EN 07/04/2005, 6:30 PM24

3Knowing your TV’s features1234Confirm your TV’s functionsSome functions written in this instruction manual may not be available for your TV.When you

4Remote control buttons and basic functionsNo. Press ToPOWER Turn on or off the TV from standby mode.MENU/OK Display menu and confirm selected functio

5Remote control buttons and basic functions (continued)The following chart shows locations of functions in menus. In this manual,location of a functio

6TV buttons and functions98 765 4IN (VIDEO-3)VRL / MONOCHANNELVOLUMEPOWER21MENUTIMEROK3Front of the TVAV-20NX50Rear of the TVAV-20NX50 AV-21YX50VLRRL

71 Connecting the aerial cable.If you connect a VCR, connect the aerial output jack of your VCRand the aerial jack on the TV with the aerial cable. Th

85 Making the initial settingsSet up your TV by pressing MENU/OK button or waiting for 15 seconds, then operate the TV menu by following the steps as

9COLOUR SYSTEMYou can select the appropriate colour system when the picture isnot clear or no colour appears.Press the COLOUR SYSTEM button to select