For Customer Use:Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information
7EnglishConnecting the Power CordBefore plugging the receiver into an AC outlet, make sure that allconnections have been made.Plug the power cord into
8EnglishBasic OperationsThe following operations are commonly used when you play any sound source.Turning the Power On and Off (Standby)On the front p
9EnglishListening Only with HeadphonesYou must turn off speakers when you listen with headphones.1. Connect a pair of headphones to the PHONES jack on
10EnglishAdjusting the Subwoofer Output LevelYou can adjust the subwoofer output level if you have selected“YES” for the “SUBWOOFER” (see page 11).Onc
11EnglishRecording a SourceYou can record any source playing through the receiver to a cassettedeck (or a CD recorder) connected to the TAPE/CDR jacks
12EnglishSetting the Speakers for the DSP ModesTo obtain the best possible surround sound of the DSP (DigitalSignal Processor) modes (see page 18), yo
13EnglishST SETTINGCrossover Frequency SettingSmall speakers cannot reproduce the bass sound very well. So, ifyou have used a small speaker for any of
14EnglishTSETTINGCONTROLDOWN UPDIGITAL 2 terminal settingDIGITAL 1 terminal settingDigital Input (DIGITAL IN) TerminalSettingWhen you use the digital
15EnglishStoring the Basic Settings andAdjustmentsYou can assign and store different sound settings for each differentplaying source. By using this fu
16EnglishTuning in Stations ManuallyOn the front panel ONLY:1. Press FM/AM to select the band(FM or AM).• Each time you press the button, the bandalte
Warnings, Cautions and Others/Mises en garde, précautions et indications diverses CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
17EnglishFM/AMSelecting the FM Reception ModeWhen an FM stereo broadcast is hard toreceive or noisyYou can change the FM reception mode while receivin
18EnglishUsing the DSP ModesThe built-in Surround Processor provides two types of the DSP (Digital Signal Processor) mode — Surround mode andDAP (Digi
19EnglishDAP modesIn order to reproduce a more acoustic sound field in your listeningroom while playing soundtracks of stereo sources, you can use DAP
20EnglishAvailable DSP Modes According to the Speaker ArrangementAvailable DSP modes will vary depending on how many speakers are used with this recei
21English65 – CENTER ++1010 – REAR•R +ENTERMENU98 – REAR•L +1TEST5. Adjust the speaker output levels.• To adjust the center speaker level, pressCENTER
22EnglishSOUND65 – CENTER +SURROUNDSURROUNDMODECONTROLDOWN UPADJUST SETTINCONTROLDOWN UP+1010 – REAR•R +ENTERMENU98 – REAR•L +TEST TONE L(Left front s
23EnglishDSP MODESOUNDMENU98 – REAR•L ++1010 – REAR•R +ENTER4EFFECTSURROUNDSURROUNDMODEAdjusting the DAP ModesOnce you have adjusted the DAP modes, th
24EnglishSURROUNDSURROUNDMODESURROUND ON/OFFSURROUND ON/OFFDSP MODEDSP MODEActivating the DSP ModesYou can use only one DSP mode at a time. When a DSP
25EnglishCOMPU LINK Remote Control SystemThe COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor ont
26EnglishOperating JVC’s Audio/Video ComponentsYou can operate JVC’s audio and video components with this receiver’s remote control, since control sig
Wall or obstructionsMur, ou obstructionStand height 15 cm or moreHauteur du socle: 15 cm ou plusFrontAvantRX-6010VBKSpacing 15 cm or moreDégagement de
27EnglishOperating Video ComponentsIMPORTANT:To operate JVC’s video components using this remote control:• Some JVC VCRs can accept two types of the c
28EnglishTroubleshootingUse this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVCservice
29EnglishSpecificationsAmplifierOutput PowerAt Stereo operation:Front channels:100 W per channel, min. RMS, driven into 8 Ω,40 Hz to 20 kHz with no mo
30EnglishFM tuner (IHF)Tuning Range: 87.5 MHz to 108.0 MHzUsable Sensitivity: Monaural: 12.8 dBf (1.2 µV/75 Ω)50 dB Quieting Sensitivity: Monaural: 21
VICTOR COMPANY OF JAPAN, LIMITEDEN, FR0301NHMMDWJEINJVCRX-6010VBK[C]COVER_f 01.2.6, 4:07 PM2
1EnglishTable of ContentsParts Identification ... 2Getting Started... 3Befo
2EnglishParts IdentificationBecome familiar with the buttons and controls on the receiver before use.Refer to the pages in parentheses for details.Fro
3EnglishGetting StartedThis section explains how to connect audio/video components and speakers to the receiver, and how to connect thepower supply.Be
4EnglishANTENNAAMLOOPFM 75 COAXIALAMEXT231Snap the tabs on the loop into theslots of the base to assemble theAM loop.Outdoor single vinyl-covered wi
5EnglishConnecting the subwoofer speakerYou can enhance the bass by connecting a subwoofer.Connect the input jack of a powered subwoofer to theSUBWOOF
6EnglishVideo component connectionsUse the cables with RCA pin plugs (not supplied).Connect the white plug to the audio left jack, the red plug to the
Kommentare zu diesen Handbüchern